




109枚の写真
所在地
Greensboro, NC
Greensboro, NC
使用状況
9,131 時間
9,131 時間
シリアル番号
CAT0014MLB9J00785
CAT0014MLB9J00785
Loading...
このロットは、IronClad保険によって保護されています
このロットは有資格検査員による十分かつ詳細な検査を受けています。安心してご購入ください。
ID番号
#14665006
ヤード内
いいえ
年
2008
製造業
モデル
資産の種類
シリアル番号またはVIN
CAT0014MLB9J00785
機能
Enclosed Cab, Air Conditioner, Air Ride Seat, Joystick Steering, Rear View Camera, Pre-Wired for Grade Control, 14 ft / 4.27 m Moldboard, Push Block, Rear Scarifier, 20.5-25 Tires
注記
The listed asset is subject to applicable title or bill of sale requirements and taxes in accordance with the laws of the state in which it is located and sold - Comes with Ironclad Assurance
















Picture, Left Front Corner
Picture, Left Rear Corner
Picture, Right Rear Corner
Picture, Right Front Corner
Serial Number / VIN
CAT0014MLB9J00785
CE Mark
No CE mark found
Hour Meter / Odometer
9131 hrs-No guarantees made as to actual hours/miles/kilometers; the inspection report reflects what can be visually observed.
Paint
Sheet Metal (fiberglass) Condition
Steps/Ladders
Hand Rails
Glass
Exterior Lights
Operational

Travel Alarm
Operational
Horn
Operational
Seat Belts
Operational
Safety Lock Out/Stop
Operational
Current Safety Manual
Current Operator/Maintenance Manual















Seats/Armrests
Mirrors
Steering Controls
Hydraulic Controls
Auxiliary Hydraulic Control
Drivetrain Controls
Dash Console
Engine Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Warning Lights
Operational
Gauges
Operational
Air Conditioner
The ambient temperature is too cold to check
Heater
Operational
Limited Function Check
The main components are in place and operational as noted.













Engine
No US EPA Label Present
A/C Compressor
In place; ambient temperature too cold to check operation
Blow-by (subjective visual observation)
No noticeable vapor or pressure
Starter
Operational
Exhaust System
Radiator
Oil Leaks
Side of engine
Fuel Leaks
No dripping leaks
Cooling System Leaks
No dripping leaks
Engine - Left Side
Engine - Right Side
Limited Function Check
The engine started and ran.









Transmission
Operational
Rear Drive Axle
Rear Tandems (Chain Drives)
Limited Function Check
The drivetrain was operational.




















Pumps (Hydraulics)
Valves
Hydraulic Tank
Hoses (Hydraulics)
Articulation Cylinders
Hydraulic Motors
Blade Lift Cylinders
Blade Angle Cylinders
Blade Side Shift Cylinders
Leak on cylinder
Saddle Positioning Cylinder
Saddle Lock Pin
Operational
Steering Cylinders
Wheel Lean Cylinders
Limited Function Check
The hydraulic system was operational.



























Y-frame
Y-frame Pivot Trunnion
Blade Tilt Frame (saddle)
Circle Frame and Brackets
Circle Wear Strips
Circle Support Brackets
Circle Gear Box
Circle Gear
Mold Board Slide Wear Strips
Articulating Center Pins
Front Axle Oscillating Pin
Steering Linkage
Wheel Tilt Linkage
Belly Pans
Limited Function Check (grader)
The main chassis components were operational in a limited check.
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Limited Function Check - Brakes
The brake system functioned, stopping and holding the machine.
Frame Condition
Tire Brands
Left Front: Yokohama, Left Middle: Firestone, Left Rear: Firestone, Right Rear: Firestone, Right Middle: Maxam, Right Front: Yokohama
Left Steer Tire
Left Front Drive Tires
Left Rear Drive Tires
Right Rear Drive Tires
Right Front Drive Tires
Right Steer Tire
Wheel Condition
Wheel Studs, Nuts, Lugs








Blade Condition
Blade Cutting Edge Condition
Scarifier
機械の詳細情報は範囲に制限があり、Ritchie Bros. Auctioneersは、ここに明記するもの以外の設備やコンポーメントの検査は行っていません。特に明記されていない限り、明示的または黙示的かにかかわらず、Ritchie Bros.は機械やそのコンポーネントに関する一切の責任を負わないものとします。機能性、快適性、あるいは関係官庁や規制機関が定める安全基準や要件に関する準拠性、特定目的への適合性、または商品性に関する表明や保証も含まれますが、これらに限るわけではありません。お客様には入札される前に必ず機械の検品を行うことをお勧めします。
機械は負荷の下でのテスト、または利用可能なすべてのギアを使用してのテストを行ったわけではありません。機械が、メーカーの仕様に従って動作されていたか保証はできません。ここで公開されている以外の機能性テストは実施されていません。個々のアンダーキャリッジコンポーネントについては選択中の写真のみが提供されています。このため、アンダーキャリッジ全体の状態を示さないことがあります。
寸法は、あくまで参考として表示されています。実際に積載された状態での寸法は、トラックやトレーラーの高さ、積載された機械の構成や位置により異なります。オークションの会場から搬出する前に、すべての積載物が運搬可能な状態になっているかの確認は、バイヤーの責任になります。全寸法は、お客様によって採寸・確認を行うようお願いします。運搬に際して、これらの寸法はあくまで参考としてお使いください。